Diy epoxy resin lamp

Diy epoxy resin lamp DEFAULT

Epoxy Resin Lamp – Step by Step Resin Lamp Instructions

February 10, 2021Categorie(s): DIY Projects, Guide

epoxy wood lamp


Making a resin lamp is a unique procedure that uses wood and epoxy resin. If you enjoy crafts and DIY, then making your own epoxy resin lamp can be a seriously rewarding process. This is a great combination of creating something useful for the house, as well as an artwork to admire. Let’s unpack the process of how to make a resin lamp step by step, and uncover exactly what you will need to pay attention to when making an epoxy lamp.





The Idea Behind Resin Table Lamps

When it comes to making crafts, there are loads of different ways to get creative, upcycle old items, and make unique creations. The resin lamp became a popular idea on Pinterest, leading many people to attempt to make them. Making your own epoxy resin lamps is not that easy at first, and it will take some time to really master the art of it. Over time, you find your style and start to create quality, unique pieces. Looking on websites like Etsy can help massively with inspiration.

epoxy lamp



Equipment Needed for a Resin Wood Lamp

Want to make your own resin table lamps? Here are some of the necessary supplies for creating these lamps.

  • Epoxy resin
  • Suitable wood
  • Wood varnish
  • Plexiglas
  • An RGB LED light
  • A module for this light
  • Silicone glue
  • Hot melting glue
  • Sandpaper
  • Polishing paste
  • Hardener
  • Wood wax
  • Cable


Suitable Epoxy Resin for Epoxy Resin Wood Lamps

lamps epoxy resin



How to Make a Resin Lamp – Step by Step Guide

Making a great resin lamp will require a few steps in order to achieve perfect results. Here are some processes to take when creating these items.


Getting the Wood Prepared

Before starting the work, preparation and planning are essential. First of all, you need to gather up some stumps of wood. You can order these online or buy them at a woodshop, but one of the best places is to gather up old oak stumps in the forest if this is a possibility. Just make sure that the wood stumps are of high quality, and won’t rot or fall apart over time.

Then it’s time to cut down the wood pieces into the right shape and size for the lamp. Using a band saw to shape and cut the wood will really help. Once cut and prepared, it’s a good idea to leave the wood to dry for a while. The longer you can let the wood dry out the better. There are a couple of different processes to follow when cleaning the wood. These are listed below:

  • Simple clean: Use a scraper, knife, or metal brush to do a rough clean of the wood surface. Scrape off any mud, bark, lichen, and dirt of the wood. This can be a messy process so it’s best done outside.
  • Deep clean: Once the wood is tidied up, you will need to really get deep in there with cleaning. Use an airstream compressor to make sure that the entire surface of the wood is completely clean.
  • Finishing: Once the wood is clean and dry, you can add a layer of varnish to enhance and protect the wood. Coat the pieces of wood with varnish, and leave them for at least 24 hours to dry completely.
wood lamp


Preparing the Lamp

While the wood is being left out to dry, you can start to prepare the work-piece for the lamp. Cut up some Plexiglas into pieces – the size of this should depend on the size of the lamp you are making. When figuring out how big to make the lamp, it’s always a good idea to design it according to the size of the room. If there is a lot of space that needs lighting up, then you will need to create a bigger lamp. Once the varnished wood is dry and ready, use a hot glue gun to stick the pieces of Plexiglas to the wooden base. The aim is to create a kind of box out of the Plexiglas with the piece of wood as the base.

epoxy resin lamp


Adding the Epoxy Resin

Now it’s time to start working with the epoxy resin. The first thing you need to do is weigh out the hardener and epoxy resin to the right proportions. Always check the manufacturer’s instructions here to make sure that you get the right mix ratio and consistency.

resin table lamp

Once measured out, you can thoroughly mix the two components of the resin together. To make sure that you get the best mixture for your resin lamp, mix this for about 20 minutes, and strain it through a filter to get rid of any dust that may have collected.

Pour the resin into the lamp mold, and place this in the degasser. This is done to remove any bubbles that may form. Leave the item in the degasser for about an hour at 20 – 24 degrees Celcius. Once you take the resin out of the degasser, leave the item to cure fully at room temperature. The time this takes will vary depending on the resin and air temperature, but it should generally be left for around two days.

resin wood lamp


Finishing the Structure

When the resin has fully cured, the wood lamp is nearly ready. Once fully cured, you can remove the Plexiglas from the solid structure. This will leave you with the unfinished lamp. Cut some wood out the bottom and insert the LED light into here. This LED light should be the size of the lamp. You can use a manual milling machine to cut out this hole in the wood, and glue the LED light into the bottom. You will also need to make some holes under the lamp for adding the cable, and the soldered cable for the LED lamp. If you use an RGB LED light, you can control this with your phone via Bluetooth. This can be a really cool feature.

resin lamp base

Then you need to join up the underside of the resin work-piece. This is best done with silicone glue and should be left for at least a full day to dry. Now the lamp is ready and dry, but the surface will be a bit uneven and rough. You can amend this by sanding down the entire surface. Start with 60 grit sandpaper, and slowly start to increase the size with each layer of sanding. Eventually, you can finish off the sanding with 2000 grit sandpaper. When hand sanding at the final stages, make the surface of the lamp slightly wet.

wood resin lamp


Finishing the Resin Lamp

Everything is all ready for use now. Before putting the lamp into place, there are just a few finishing touches that should be done. Polish the epoxy lamp’s surface with some polishing paste that you can use on car headlights. Once polished, chafe the resin lamp with some wax. And there you have it, the lamp is complete and ready to use!

resin lamp

Making resin table lamps can be quite a time consuming and hands-on process. However, the results of your epoxy lamp masterpiece will be sure to have you feeling proud and happy with your work. Making a resin wood lamp is a satisfying process, and it will leave you with a product that you can enjoy for many years to follow.




In this blogpost you get an exclusive tutorial on epoxy resin wood lamps. I’ll show you step by step how you can make these unique pieces with resin and wood and which materials are best suited for this. You will get important insider information and I will tell you what you should pay attention to so that these noble artpieces also succeed.




How Did the Idea of making Epoxy Resin Wood Lamps appear?

Since childhood, my brother and I have dreamed of creating crafts. We tried to make different products: chandeliers from a wooden wheel, wooden handles, pictures, etc. The idea of making epoxy resin wood lamps appeared on Pinterest. Our first attempts were not satisfying but we didn’t stop. After some time, we found our style, but we are still improving on things. After visiting some conference about starting a business, I met a young man who made wooden toys. He showed me the website known as Etsy. All of these circumstances have inspired me to move in this direction and make my dream come true.

epoxy lamp



Supplies for Making an Epoxy Resin Wood Lamp

  • Wood (Oak, Roots)
  • Suitable Epoxy Resin
  • RGB LED Light
  • Module for RGB Light
  • Varnish for Wood
  • Plexiglas
  • Hot-melt Glue
  • Sandpaper
  • Polishing Paste
  • Wax for Wood
  • Cable
  • Silicone Glue
  • Hardener


Suitable Epoxy Resin for Epoxy Resin Wood Lamps


lamps epoxy resin



Step by Step Tutorial for Epoxy Resin Wood Lamp



  • Our work doesn’t start in the workplace. Let’s take a look at what happens before that. You have to go to the forest or any other place where you can gather old oak stumps. If this is not possible, you can buy wood in the shop or order online. Choose good quality stumps that are not rotten or destroyed.
  • The next step is to bring them to your workplace and cut them into the pieces you need for your lamp. We use a band-saw to cut off the angles and to shape it. When you are done with that, put all of your wood in a place where it can dry for some time.

wood lamp


Preparation of the Wood Consists of Several Stages

  1. Rough Cleaning: For this process, use a knife or metal brush to clean the mud and tree bark off of the wood. You’d better do it outside or find a suitable place for such dirty work.
  2. Deep Cleaning: This stage follows exactly after rough cleaning. Using an airstream compressor, blow small pieces of mud and dust from the wood to make it completely clean.
  3. Varnishing: At the last stage of preparation, you must cover the wooden pieces with varnish and leave them to dry for 24 hours.

epoxy resin lamp


Preparation of the Lamp Work-Piece

While our wood is drying, take some Plexiglas and cut it into pieces. The size of the pieces depends on the size of the lamp that you want to make.

Tip: Choose the size of the lamp according to the room where you or someone else wants to put it. If the room is big, try to make appropriate lamp so that it can lighten the room and create a special atmosphere.

You will then take the clean and varnished wood pieces and glue them to the Plexiglas bottom with hot-melt glue. In the end, the walls of the Plexiglas work-piece must be glued together in such a way that you get an empty box with a wooden bottom.

ebook epoxy resin


Pouring the Epoxy Resin

  • At this stage, we will work specifically with epoxy resin. Here we use epoxy resin of Ukrainian production which has already tested to make sure that it is perfect. First, weigh the resin and hardener separately – the proportion is 100 to 27.
  • Put the epoxy resin and hardener in one container and mix everything for 15-20 minutes. To clean the mixture, strain it through a filter that gathers all dust and pour into the ready-made work-piece.

wood resin lamp

  • After that, put the work-piece with epoxy resin mixture in the degasser so as to take away bubbles (for approximately one hour if the room temperature is 20-24 degrees Celsius). After one hour of degassing, leave the product to solidify for two to three days in a place with a room temperature of 18 to 24 degrees Celsius.

resin wood lamp


Finishing the Work-Piece

  • Finally, you are close to completing your epoxy resin wood lamp. After two to three days of drying, take off the Plexiglas from the solid work-piece. You now have your lamp but it is still unfinished.
  • Then take some wood and cut out the bottom. Inside the bottom, insert an LED light that is the size of the lamp. For this, cut a small concavity in the wooden bottom with a manual milling machine. This concavity is for the LED light. Take your LED light and glue it to the bottom.

resin lamp base

  • In addition to that, make holes in this wooden bottom for a cable and a soldered cable for the LED light. You now have the light in your lamp. I buy my LED lights from a local shop with a voltage of 100-240 V. An RGB LED light can be controlled with a cell phone programmer using Bluetooth.
  • The next step is to join the bottom of the epoxy resin work-piece. To do that, you can use silicone glue. When you are done with that, don’t forget to leave the lamp to dry for one day.
  • After drying you will see that the surface of the lamp is rough and uneven. To take that away, grind all sides of the lamp using sandpaper and a grinder machine. You have to be patient and start from grit size 60 and grind for approximately 5 to 10 minutes. You have to change the grit of the sandpaper each time to achieve better results. So you would move from grit size 60 and increase it to size 120, 240, 320, 400, and 600 step-by-step.
  • The sanding process doesn’t stop at this stage: as this is a handmade product, you will need to use your hands. Sand the lamp with your hands using sandpaper grit size 1000, followed by 1500 and 2000. When you grind or sand lamps with your hands, you should make the surface of the lamp a little bit wet.

resin table lamp



Finishing the Lamp

One of the last steps is polishing the epoxy resin surface of the lamp with polishing paste for car headlights. Finally, chafe the lamp with some wax. Now you can hold your lamp in your hands and feel satisfaction from the result that you can see.

I hope that you can do your best following my tutorial. But don’t forget to express your ideas and your dreams in your creation! Don’t make a copy, make a masterpiece – it is priceless!

resin lamp



Oleksandr Dembitskiy

Oleksandr Dembitskiy was born and still lives in the Ukraine (eastern Europe). He has already graduated from two Universities and got a Master’s degree in economics. For a long time, he worked as a credit specialist at the bank, and it took him almost ten years to find his passion for his real job. Epoxy resin wood crafts became his real challenge that has completely changed his life. It all started as a hobby, where he and his brother would try to spend time together by making masterpieces with their hands. They experimented with different materials and made different things. Oleksandr was always interested in crafts, but his main highlight was to create something unique, special and personal. Now working as an artist, he tries to be in touch with every customer to discuss their desires and wishes. Oleksandr makes wooden epoxy resin lamps to bring comfort and peace to people’s homes. He doesn’t think of this process as just a business, but as his way of freedom and to show the beauty of the world created by God. He always experiments with light colors and likes to discover new modern techniques (such as RGB color). This work helps him to open his imagination and bring it to life, so that every person can enjoy the magic glitter of wooden Korchi lamps.


  1. Skyrim old orc
  2. American tv series 2017
  3. Wonder woman gif
  4. Waze save current location
  5. Rv construction materials

Introduction: Epoxy Resin and Walnut LED Night Lamp

This time I had the main goal to try a very first-time epoxy resin casting. I’ll show you how from epoxy resin, American walnut, and cheap electronics I made this stunning LED night lamp.

How I did it - you can check by looking DIY video or you can follow up instructions bellow.

For this project you will need:


Walnut 20x20x120mm and 20x20x200 ( or other your preferred wood)

Wood glue, CA glue

Transparent epoxy resing for deep casting

Fairy string LED light

Plastic sheets for casting form (mold)

Hot glue

Micro USB connector

Buffing pad and automotive polishing paste

Danish oil for wood finish

Sandpaper 400, 800, 1000, 1500 grit.

Electric tape


Belt sander with 80 grit sandpaper

Miter saw

Palm router

Orbital sander with 120, 240 and 320 grit sandpaper

Drill and bits

Clamps and some other usual bits and bobs which is laying around the workshop.


Soldering iron and solder

Step 1: Materials

One of the main materials will be those American walnut pieces. Since I don't have a thickness planer - I ordered to prepare all workpieces of the required size. They all are in 20 by 20 millimeters. Talking about length - the longer ones are in 200, and the shorter in 120-millimeter length.

Step 2: The First Glue Up

The very first step is to glue every 4 pieces together by misaligning them in a random pattern. The same procedure was done with longer pieces too.

When the glue was dried - prepared the surface for the next glue-up by sanding down to get a nice flat surface.

Step 3: The Second Glue-up

The second glue-up was similar to the first one. The only difference was that this time I glued 4 already pre-glued boards to a solid rectangular wood block.

Glue dried and I got two solid walnut blocks.

Step 4: Flattening Ends

Used miter saw and flattened one end of each block. Sacrificial plywood pieces helped to avoid any walnut tear outs.

Cleaned cut ends with the sandpaper. Take a look at that nice end grain!

Step 5: Few Holes for Electronics

I used a palm router and milled a hole on the flat walnut block end. Here will be hidden all electronics parts.

Drilled 3-millimeter hole all the way thru the block. Thru this hole will be wired LEDs from top to bottom.

Step 6: Preparing Wood Surface for the Epoxy

I mixed a small part of the same epoxy resin which will be used later and covered all wood surfaces which will have a contact with epoxy resin pour. This should seal the wood and prevent the formation of bubbles in the casting.

Step 7: The Electronics

I bought this fairy string LED light with 100pcs of individual colored LEDs connected inline. It could be powered from any USB power source, like the power bank, smartphone charger, laptop and etc. My fairy string light version had a controller that gives a few different operating modes. However most of the time I’m planning to use this one - constant light.

Cut the power wire and managed it all the way thru. I used hot glue to seal the hole and fixed the wire in it.

Step 8: The Casting Mold

From random plastic that layed around I start making the outer form for epoxy resin pour. Placed on the side a straight reference and adjusted to my preferred spacing of wood pieces. To seal up all edges I used hot glue. All seams should be weather tight because the resin will find the smallest hole or crack and will follow out. I take my time and sealed all joints to avoid the mentioned situation. On the top, I made a small barrier to keep epoxy resin overfill.

Step 9: The Epoxy Resing

Ok, the epoxy resin. I bought locally this highly transparent and UV stabilized epoxy casting resin. It’s designed to use in deep pours, like up to 10 centimeters. Mine will be only 8 centimeters deep so I should work just fine. I poured the resing and hardener according to the indicated mixing ratio and mixed very very well. After that, I gave a light transparent color tone by adding a few drops of turquoise pigment. Once again a bit of mixing and I poured the resin into the form.

This is very slow curing epoxy resin so all bubbles will escape naturally. Here is the casting after 20 minutes - I can’t see any of bubbles (last picture).

Step 10: Taking Out

This epoxy requires 3 days to fully cure, but I left it a bit longer. One week later the resin was rock solid and it was the perfect time to remove from the mold.

Step 11: Lot of Sanding

To clean all sides I used a belt sander and 80 grit sandpaper. When the job was done here I changed it to an orbital sander and passed with 120, 240, and 320 grit sandpaper.

After that moved to the finer grits and sanded by hand. Started with 400 grit, then 800 grit, 1000 and finished with 1500 grit sandpaper.

Step 12: Polishing the Epoxy

To bring back the shine I used 8 centimeters buffing pad on a drill and a regular automotive polishing paste. After good 20minutes of polishing the shine is back.

Step 13: Working on Electronic Part

It is time to rework the electronic part so, that It will fit in our prepared place. First of all, I need to desolder a power on/off button and relocate it. Second - I no need this USB connector anymore, so it should be desoldered too. All electronics should fit inside this hole.

Step 14: Some Soldering

To fix the power button in needed place I desoldered from the mainboard and made a simple housing with extended two wires. To fix it in the palace I use CA glue and activator. Soldered micro USB port to the power IN terminals, extended wires from the ON/OFF button, and lastly soldered the fairy light wires.

Step 15: Closing the Internals of Light

Finished up with some electric tape and hidden inside the hole. CA glue helped to fix permanently the micro USB port in needed place. With the thin piece of walnut and a few drops of wood glue - closed the hole.

Step 16: Finishing the Wood

Finished up with some electric tape and hidden inside the hole. CA glue helped to fix permanently the micro USB port in needed place. With the thin piece of walnut and a few drops of wood glue - closed the hole.

Step 17: The Result

And here it is - clear epoxy resin and walnut fairy string LED lamp.

As for the very first project with the epoxy resin casting - the result exceeded my expectations. Despite a few small mistakes made during the project - I’m more than happy with the finished product. It’s a pity that the camera cannot transmit a real view of how it looks in real. If you ever tried to film a lamp or any light source, you understand my pain.

Step 18: BONUS

By the way, do you remember those two offcuts left by flattening the main pieces? They weren’t thrown out. I made another smaller and darker lamp version.

I used epoxy resin made for casting for the first time, but certainly not the last. I will definitely use it again in the future, especially in projects where I will combine several different materials by using epoxy resin.

1 Person Made This Project!

Did you make this project? Share it with us!


  • Robots Contest

    Robots Contest
  • Plastic Challenge

    Plastic Challenge
  • 3D Printed Student Design Challenge

    3D Printed Student Design Challenge

Even the most delicious food gets boring, taking it regularly, but never bread. And also classic sex, three times a week, no more, that is, breakfast, lunch and dinner. - You think so philosophically, you would have to work as the head of the department, and not manage public catering, Roman joked.

Epoxy lamp diy resin

June 11, 12:00 Max Kisa, I also want to sleep with you. I want to wake you up by starting forward movements with a member in you, so that you wake up from this. I want you kitty. June 11, 12: 06 Albina Zayka Zaya, I want that too !!!!!!!!!!!. June 11, 12: 24 Max Zay I want to fuck you for a long time and then cum in your mouth and do it every time, how do you look at.

Easy making Epoxy Resin lamp Magical purple - Diy Resin Art

And suddenly I saw a part of her chest in an open blouse. A slightly tanned body with mounds that I could see. She hissed: Give it back, my.

Similar news:

No, but you believe me. You just tell me, you believe me that I didn't fuck with anyone, she repeated. Yes, I believe, I believe, he replied, thinking that she was just saying this in delirium.

20912 20913 20914 20915 20916